All times are UTC


It is currently Wed Nov 27, 2024 10:43 am



Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: Dry or not...
PostPosted: Thu Jun 16, 2011 2:58 pm 
Loremaster
Loremaster
Offline

Joined: Mon Jun 06, 2011 7:07 am
Posts: 2088
Hi guys... Tomorrow probably i will buy my first minis and i have painting questiona...
1)When you spray your minis do you begin paintng immidielty?
2) Whn you add a colour do you wait for it to dry or you aplly the next colour?
3)When a painting guide says drybrush it eman your brush mus not be wait right?
:)
Top
  Profile  
Reply with quote  
 Post subject: Re: Dry or not...
PostPosted: Thu Jun 16, 2011 3:29 pm 
Loremaster
Loremaster
User avatar
Offline

Joined: Sat Jun 07, 2008 6:26 pm
Posts: 1143
Location: In the midst of the chaos...
1) No, I give them time to dry, which can be helped with a hair dryer, just don't hold it too close for too long... I then inspect the minis for any areas that the spray has missed and touch them up by brush, and allow this to dry. (I get through a lot of coffee...)

2) Unless you are wet blending, the paint should be allowed to dry before you add the next layer. Drying time will depend on how much you water the paint down.

3) Dip the bush in paint and wipe most of it off on a tissue or towel, this is what you would call over brushing, in that passing the brush over the mini deposits a lot of colour and can be used for quick basecoating. It is still a messy practise and should be done before any more detailed painting.

Or (both techniques are pretty similar)

Dip the bush in paint and wipe most of it off on a tissue or towel, wipe it again, and again, and again. There should be almost no visible paint on the bristles, and this is what you would call dry brushing. Pass the brush over the model and you will (hopefully) get a very slight amount of paint deposited on the mini. It sometimes leads to a slightly dusty look, but this can be covered by multiple drybrushes and glazing or washes.

_________________
Studio gaarew; Gaming armies, by gamers, for gamers.
Top
  Profile  
Reply with quote  
 Post subject: Re: Dry or not...
PostPosted: Thu Jun 16, 2011 7:03 pm 
Loremaster
Loremaster
Offline

Joined: Mon Jun 06, 2011 7:07 am
Posts: 2088
Thanks very much :rofl:
Top
  Profile  
Reply with quote  
 Post subject: Re: Dry or not...
PostPosted: Sat Jun 18, 2011 8:21 am 
Elven Warrior
Elven Warrior
User avatar
Offline

Joined: Thu Dec 04, 2008 7:20 am
Posts: 572
Location: Adelaide, Australia
Also, when drybrushing, a good way to gauge whether there is enough paint on the brush is to wipe it over your finger. It should only put the paint on the high points, showing your fingerprint :). If not, then not the right amount of paint 8)
Top
  Profile  
Reply with quote  
 Post subject: Re: Dry or not...
PostPosted: Fri Jun 24, 2011 8:52 pm 
Kinsman
Kinsman
User avatar
Offline

Joined: Thu May 27, 2010 10:53 pm
Posts: 161
With drybrushing, the consistency must me right. Too thin and it wont work, too thick and it will leave irregular blotches and will clump up. Ideally I dont use drybrushing with acrylics if I can help it as oil based paint is better as it has a longer drying time. However, I tend to use a piece of rag or kitchen towel and rub the paint out on that. I use my old brushes for this but have converted a few brushes as dry brushers as you do need a good brush. Just make sure you dont use your best brush for the job as it will ruin the bristles. And I find flat brushes work better than rounded ones (as in the bristles!)
Top
  Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 17 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: