The One Ring
https://ww.one-ring.co.uk/

.
https://ww.one-ring.co.uk/viewtopic.php?f=7&t=23255		 Page 1 of 1
Author:  Éomer [ Sun Jun 17, 2012 1:26 pm ]
Post subject:  .
.
Author:  Telchar [ Sun Jun 17, 2012 6:46 pm ]
Post subject:  Re: Building my first gaming board, please help
I haven't built a board myself yet, so I can't help you with material choices etc.

Foldable legs seem very difficult to make and will add a lot of weight to the board (thus making it more cumbersome, etc). If you want it to stand by itself, I'd just put some real legs under it on the spot. You can also make very broad supports (we used to make them out of big plastic boxes until we cleared a proper table to lay our gaming mat on) and just rest it on top of that.

For size, 6'x4' seems standard, though I (addicted to huge Napoleonic and WW2 battles as I am) would make it larger. Remember, you can allways use a non-crossable modular river to make it smaller if you want.
Author:  Oldman Willow [ Mon Jun 18, 2012 12:58 am ]
Post subject:  Re: Building my first gaming board, please help
Quote:
What kind of wood should I use? Plywood?

1/2 inch construction grade. http://woodworking.about.com/od/plywood ... Grades.htm
Quote:
What measures are prefered? I will be playing both LotR and WH40K on the board.

4'X6'
Quote:
I will most likely place the board on the kitchen table but please share your advice concerning attaching foldable legs to the board.

see links
http://www.homedepot.com/webapp/wcs/sto ... -100048820
You may want to frame the plywood See links
http://woodworking.about.com/od/shopequ ... able_4.htm
Note a shop table needs to be way stronger than a gaming board but the principle is the same.

For the kitchen table you might want to get a two inch 4'X8' of medium density Styrofoam and paint it. It will be much lighter than plywood and cost about the same as mid grade plywood. You could even cut it in half and hinge it with duct tape. I made a ten 4'X6' tables like that for a convention. They lasted a few years but I cut them up and started using the folding legs in the first link with plywood tables instead.
Author:  Slythar [ Mon Jun 18, 2012 1:34 am ]
Post subject:  Re: Building my first gaming board, please help
My table is 4' x 6' x 1/2" MDF cut in half to 2x6. A dining table can support it without additional legs and it can still fit in my Hyundai Accent.
Author:  Oldman Willow [ Mon Jun 18, 2012 4:18 am ]
Post subject:  Re: Building my first gaming board, please help
Quote:
My table is 4' x 6' x 1/2" MDF cut in half to 2x6.

The disadvantage of MDF is it won't hold nails or wood screws for that mater so you won't be able to attach the hardware that comes with the folding legs I recommended. The two 2'X6' as sections has the advantage of fitting the small car. So would three 2'X4' sections.
Image
One of my portable tables at my new house. 10 will fit in my pick up truck :lol:
Image
An old photo of the game table at my old house. It is a box built from two 1/2" 4'X6 plywood sheets and two 2"X6" X12"s. The top sheet was cut into three 2'X4' sections so that I could use the inside of the box for storage. It rest on metal map files.
I don't build permanent boards for my self any more. They are just to hard to store and transport. I use table covers and modular terrain.
Author:  warhammergamingnl [ Mon Jun 18, 2012 5:06 pm ]
Post subject:  Re: Building my first gaming board, please help
Awesome terrain pieces on that board! ;O
Author:  Oldman Willow [ Mon Jun 18, 2012 10:47 pm ]
Post subject:  Re: Building my first gaming board, please help
Quote:
Awesome terrain pieces on that board!

Thanks :!:
Image
I use the foot lockers to transport the terrain when I play at the Hobby Shop or Treefort.
Page 1 of 1 All times are UTC
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/